By Alex Phillips, Business Development Manager
How smart radar-controlled crushing unlocked nameplate performance at a Western Australian iron ore operation.
Large hematite iron ore plants consistently underperform their nameplate design throughput. At one direct shipping ore (DSO) operation in Western Australia, the root cause was instrumentation failure in the crushing circuit.
If your plant is in the same position, this blog post outlines how better measurement closed the gap.
The gap between installed and realised capacity
Picture the crushing circuit before the project. Legacy level sensors struggled in the dust and the high volume of material, so readings were unreliable. Operators did the sensible thing: they built in safety margins and relied on manual or semi-automated control.
The result was inconsistent choke-fed operation and highly variable feed to the secondary and tertiary crushers. Every week, the site saw 3.2 empty-bin crusher trips and 2.1 overfill protection events. The mean time between failures (MTBF) was just 68 hours.
Behind those numbers were people monitoring bins by hand in dusty conditions, and maintenance teams stuck in reactive mode.
Why surge bins are so hard to measure
The circuit itself is a familiar one. Run-of-mine ore is crushed to around 200 mm in the primary crusher, then passes through a secondary gyratory and tertiary cones working with vibrating screens to produce a product of about 12 mm.
The surge bins in between are where measurement gets tough. Heavy dust weakens sensor signals. The material surface is uneven, so a single-point reading can be badly wrong. Vibration, temperature swings and limited access make it worse.
Seeing through the dust with radar
The answer was two complementary radar solutions, deployed in parallel. A 2D scanning radar watches the surge bins, and a high-frequency 1D radar monitors the crusher cavity.
Dust, vapour and tough process conditions no longer get in the way, because the 76 GHz radar technology is unaffected by them. It reads the level more than 8,000 times a second, compared with 2–3 Hz for the legacy sensors, and it scans the whole bin surface instead of a single point.
In practice, operators can see how full each bin really is. The radar turns a cross-section of the bin into configurable virtual bins, with up to 10 zones for targeted high and low level alarms, and gives absolute and relative fill levels. That takes the guesswork out, and the assumptions that cost production with it.
Integration is simple. The radar plugs straight into the distributed control system (DCS) using Modbus TCP. In the crusher, cavity level now feeds straight into PID speed control, with filtering done on the device, so no extra filtering logic is needed in the DCS.

Rolling it out without stopping production
The team focused on seven critical surge bins and worked in three phases. First came the site survey and design (weeks 1–3), with radar installed during planned shutdowns and sensors positioned for full bin visibility. Next was DCS integration (weeks 3–4), with automated feeder and conveyor control plus protection alarms and interlocks.
Finally, a parallel run and ramp-up (months 3–6) validated the radar against the existing sensors before set-points were raised step by step. The result was zero production downtime during implementation.
What changed across 12 months
The improvements held across the full 12 months after commissioning. Tertiary crusher throughput climbed from 540 tph to more than 800 tph, an increase of over 40% across nine crushers
Here are the headline results:
- Empty-bin crusher trips fell 81%, from 3.2 to 0.6 per week
- Overfill protection events fell 81%, from 2.1 to 0.4 per week
- MTBF more than doubled, from 68 to 142 hours
- Product size stayed within ±1.5 mm of the P80 target 89% of the time, up from 64%
Choke-fed operation now exceeds 85% of operating time, and feed rate variability is down by about 50%. Specific energy fell by about 8% per tonne produced.

The business case
Total installed cost was around AUD 2 million, with no lost production and no new civil structures. Across the secondary and tertiary circuits, the annualised throughput uplift is about 12%.
At AUD 110/t (Fe 62% CFR), each additional 1 mtpa is worth roughly AUD 26 million in gross revenue. Payback is under one quarter at the base case. Even with a 30% throughput haircut and AUD 80/t iron ore, the NPV stays strongly positive and payback is around two quarters. That is before counting energy savings and lower maintenance costs.
Lessons for other operations
Nothing here is unique to iron ore. The same architecture suits copper, gold and base metals, and it works alongside existing control systems.
Three practices made the difference:
- Focus on the critical surge bins first
- Use staged commissioning and clear KPIs
- Hand over control only after the data has been validated
Looking ahead, advanced process control (APC) and machine learning could unlock further gains across the comminution circuit.
Start closing your own gap
In short, better measurement made the difference. Tertiary crusher throughput rose by over 40%, trips and overfill events fell 81%, MTBF more than doubled and energy per tonne fell by about 8%.
If your crushing circuit is running below nameplate, the cause may be hiding in your measurement. To explore what radar-controlled crushing could do for your site, get in touch with Alex Phillips, Business Development Manager, at alex.phillips@hexagon.com, or visit hexagon.com.